Developer Documentation

ADC CLI Commands

L3Param

June 28, 2023

Contributed by:

C

The following operations can be performed on “L3Param”:

show L3Param

Displays the settings of global Layer 3 parameters.

Synopsis

show L3Param

Arguments

Output

srcnat Perform NAT if only the source is in the private network

icmpGenRateThreshold NS generated ICMP pkts per 10ms rate threshold

overrideRnat USNIP/USIP settings override RNAT settings for configured service/virtual server traffic..

dropDFFlag Enable dropping the IP DF flag.

mipRoundRobin Enable round robin usage of mapped IPs.

externalLoopBack Enable external loopback.

tnlPmtuWoConn Enable/Disable learning PMTU of IP tunnel when ICMP error does not contain connection information.

usipServerStrayPkt Enable detection of stray server side pkts in USIP mode.

forwardICMPFragments Enable forwarding of ICMP fragments.

dropIPFragments Enable dropping of IP fragments.

AclLogTime Parameter to tune acl logging time

implicitACLAllow Do not apply ACLs for internal ports

dynamicRouting Enable/Disable Dynamic routing on partition. This configuration is not applicable to default partition

ipv6DynamicRouting Enable/Disable IPv6 Dynamic routing

allowClassEIPv4 Enable/Disable IPv4 Class E address clients

show l3param

set L3Param

Set Layer 3 related global settings on the Citrix ADC

Synopsis

set L3Param [-srcnat ( ENABLED

DISABLED )] [-icmpGenRateThreshold ] [-overrideRnat ( ENABLED

DISABLED )] [-dropDFFlag ( ENABLED

DISABLED )] [-mipRoundRobin ( ENABLED

DISABLED )] [-externalLoopBack ( ENABLED

DISABLED )] [-tnlPmtuWoConn ( ENABLED

DISABLED )] [-usipServerStrayPkt ( ENABLED

DISABLED )] [-forwardICMPFragments ( ENABLED

DISABLED )] [-dropIPFragments ( ENABLED

DISABLED )] [-AclLogTime ] [-implicitACLAllow ( ENABLED

DISABLED )] [-dynamicRouting ( ENABLED

DISABLED )] [-ipv6DynamicRouting ( ENABLED

DISABLED )] [-allowClassEIPv4 ( ENABLED

DISABLED )]

Arguments

srcnat Perform NAT if only the source is in the private network

Possible values: ENABLED, DISABLED Default value: ENABLED

icmpGenRateThreshold NS generated ICMP pkts per 10ms rate threshold Default value: 100 Minimum value: 0

overrideRnat USNIP/USIP settings override RNAT settings for configured service/virtual server traffic..

Possible values: ENABLED, DISABLED Default value: DISABLED

dropDFFlag Enable dropping the IP DF flag.

Possible values: ENABLED, DISABLED Default value: DISABLED

mipRoundRobin Enable round robin usage of mapped IPs.

Possible values: ENABLED, DISABLED Default value: ENABLED

externalLoopBack Enable external loopback.

Possible values: ENABLED, DISABLED Default value: DISABLED

tnlPmtuWoConn Enable/Disable learning PMTU of IP tunnel when ICMP error does not contain connection information.

Possible values: ENABLED, DISABLED Default value: ENABLED

usipServerStrayPkt Enable detection of stray server side pkts in USIP mode.

Possible values: ENABLED, DISABLED Default value: DISABLED

forwardICMPFragments Enable forwarding of ICMP fragments.

Possible values: ENABLED, DISABLED Default value: DISABLED

dropIPFragments Enable dropping of IP fragments.

Possible values: ENABLED, DISABLED Default value: DISABLED

AclLogTime Parameter to tune acl logging time Default value: 5000 Minimum value: 0

implicitACLAllow Do not apply ACLs for internal ports

Possible values: ENABLED, DISABLED Default value: ENABLED

dynamicRouting Enable/Disable Dynamic routing on partition. This configuration is not applicable to default partition

Possible values: ENABLED, DISABLED Default value: DISABLED

ipv6DynamicRouting Enable/Disable IPv6 Dynamic routing

Possible values: ENABLED, DISABLED Default value: DISABLED

allowClassEIPv4 Enable/Disable IPv4 Class E address clients

Possible values: ENABLED, DISABLED Default value: DISABLED

show l3param

unset L3Param

Use this command to remove L3Param settings.Refer to the set L3Param command for meanings of the arguments.

Synopsis

unset L3Param [-srcnat] [-icmpGenRateThreshold] [-overrideRnat] [-dropDFFlag] [-mipRoundRobin] [-externalLoopBack] [-tnlPmtuWoConn] [-usipServerStrayPkt] [-forwardICMPFragments] [-dropIPFragments] [-AclLogTime] [-implicitACLAllow] [-dynamicRouting] [-ipv6DynamicRouting] [-allowClassEIPv4]

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Was this helpful

L3Param

June 28, 2023

Contributed by:

C

June 28, 2023

Contributed by:

C

In this article

show L3Param
set L3Param
unset L3Param

Was this helpful