td Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0. Minimum value: 0 Maximum value: 4094

ownerGroup The owner node group in a Cluster for this rnat rule. Default value: DEFAULT_NG

stat rnat

Display statistics for rnat sessions.

Synopsis

stat rnat [-detail] [-fullValues] [-ntimes ] [-logFile ] [-clearstats ( basic

full )]

Arguments

detail Specifies detailed output (including more statistics). The output can be quite voluminous. Without this argument, the output will show only a summary.

fullValues Specifies that numbers and strings should be displayed in their full form. Without this option, long strings are shortened and large numbers are abbreviated

ntimes The number of times, in intervals of seven seconds, the statistics should be displayed. Default value: 1 Minimum value: 0

logFile The name of the log file to be used as input.

clearstats Clear the statsistics / counters

Possible values: basic, full

Output

Counters

Bytes Received (rnatRxBytes) Bytes received during RNAT sessions.

Bytes Sent (rnatTxBytes) Bytes sent during RNAT sessions.

Packets Received (rnatRxPkts) Packets received during RNAT sessions.

Packets Sent (rnatTxPkts) Packets sent during RNAT sessions.

Syn Sent (rnatTxSyn) Requests for connections sent during RNAT sessions.

Current RNAT sessions (rnatSessions) Currently active RNAT sessions.

Example

stat rnat

stat MapDomain

unset rnat

Use this command to modify the parameters of configured Reverse NAT on the system..Refer to the set rnat command for meanings of the arguments.

Synopsis

unset rnat (( \[]) | \( \[-redirectPort])) \[-td <positive\_integer>] \[-natIP <ip\_addr|\*>@ ...] \[-srcippersistency] \[-ownerGroup ] \[-useproxyport] \[-connfailover]

set rnat

Modifies parameters of an RNAT rule.

Synopsis

Arguments

network IPv4 network address on whose traffic you want the Citrix ADC to do RNAT processing.

netmask Subnet mask associated with the network address.

natIP Any Citrix ADC-owned IPv4 address except the NSIP address. The Citrix ADC replaces the source IP addresses of server-generated packets with the IP address specified. The IP address must be a public Citrix ADC-owned IP address. If you specify multiple addresses for this field, NAT IP selection uses the round robin algorithm for each session. By specifying a range of IP addresses, you can specify all Citrix ADC-owned IP addresses, except the NSIP, that fall within the specified range.

aclname Name of any configured extended ACL whose action is ALLOW. The condition specified in the extended ACL rule isused as the condition for the RNAT6 rule.

redirectPort The port number to which the packets are redirected. Minimum value: 1 Maximum value: 65535

natIP The NAT IP(s) assigned to the RNAT.

srcippersistency Enables the Citrix ADC to use the same NAT IP address for all RNAT sessions initiated from a particular server.

Possible values: ENABLED, DISABLED Default value: DISABLED

useproxyport Enable source port proxying, which enables the Citrix ADC to use the RNAT ips using proxied source port.

Possible values: ENABLED, DISABLED Default value: ENABLED

ownerGroup The owner node group in a Cluster for this rnat rule. Default value: DEFAULT_NG

connfailover Synchronize all connection-related information for the RNAT sessions with the secondary ADC in a high availability (HA) pair.

Possible values: ENABLED, DISABLED Default value: DISABLED

show rnat

Display the Reverse NAT configuration.

Synopsis

show rnat

Arguments

Output

network The network address.

netmask Subnet mask associated with the network address.

natIP Nat IP Address.

aclname Name of any configured extended ACL whose action is ALLOW. The condition specified in the extended ACL rule isused as the condition for the RNAT6 rule.

redirectPort The port number to which the packets are redirected.

srcippersistency Enables the Citrix ADC to use the same NAT IP address for all RNAT sessions initiated from a particular server.

useproxyport Enable source port proxying, which enables the Citrix ADC to use the RNAT ips using proxied source port.

cfgflags This contains the flags for RNAT in DB

ownerGroup The owner node group in a Cluster for this rnat rule.

connfailover Synchronize all connection-related information for the RNAT sessions with the secondary ADC in a high availability (HA) pair.

devno count stateflag

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Was this helpful

rnat

June 28, 2023

Contributed by:

June 28, 2023

Contributed by:

rnat

clear rnat

Synopsis

Arguments

stat rnat

Synopsis

Arguments

Output

Counters

Example

Related Commands

unset rnat

Synopsis

set rnat

Synopsis

Arguments

show rnat

Synopsis

Arguments

Output

In this article