bridgegroup¶
The following operations can be performed on "bridgegroup":
rm| bind| unbind| set| unset| add| show|
rm bridgegroup¶
Remove the bridge group created by the add bridge group command.
Synopsis¶
rm bridgegroup
Arguments¶
id An integer that uniquely identifies the bridge group that you want to remove from the Citrix ADC. Minimum value: 1 Maximum value: 1000
bind bridgegroup¶
Bind a vlan or an ip address to a bridgegroup.
Synopsis¶
bind bridgegroup
Arguments¶
id The integer that uniquely identifies the bridge group. Minimum value: 1 Maximum value: 1000
vlan An integer that uniquely identifies the VLAN that you want to bind to this bridge group. Minimum value: 2 Maximum value: 4094
IPAddress A network address or addresses to be associated with the bridge group. You must add entries for these network addresses in the routing table before running this command.
netmask A subnet mask associated with the network address.
td Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0. Minimum value: 0 Maximum value: 4094
ownerGroup The owner node group in a Cluster for this vlan. Default value: DEFAULT_NG
Example¶
bind bridgegroup 1 -vlan 2
unbind bridgegroup¶
Unbinds the specified VLANs or IP addresses from a bridge group.
Synopsis¶
unbind bridgegroup
Arguments¶
id Integer that uniquely identifies the bridge group. Minimum value: 1 Maximum value: 1000
vlan ID of the VLAN to unbind from this bridge group. Minimum value: 2 Maximum value: 4094
IPAddress Network address associated with the bridge group.
netmask The network mask for the subnet defined for the bridge group.
td Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0. Minimum value: 0 Maximum value: 4094
ownerGroup The owner node group in a Cluster for this vlan. Default value: DEFAULT_NG
set bridgegroup¶
Set Bridge group parameters.
Synopsis¶
set bridgegroup
Arguments¶
id An integer value that uniquely identifies the bridge group. Minimum value: 1. Maximum value: 1000. Minimum value: 1 Maximum value: 1000
dynamicRouting Enable dynamic routing for this bridgegroup.
Possible values: ENABLED, DISABLED Default value: DISABLED
ipv6DynamicRouting Enable all IPv6 dynamic routing protocols on this bridge group. For this setting to work, you must configure IPv6 dynamic routing protocols from the VTYSH command line. For more information about configuring IPv6 dynamic routing protocols on the Citrix ADC, see the Dynamic Routing chapter of the Citrix ADC Networking Guide.
Possible values: ENABLED, DISABLED Default value: DISABLED
Example¶
set bridgegroup 1 -dynamicRouting ENABLED
unset bridgegroup¶
Use this command to remove bridgegroup settings.Refer to the set bridgegroup command for meanings of the arguments.
Synopsis¶
unset bridgegroup
add bridgegroup¶
Create a Bridge group.
Synopsis¶
add bridgegroup
Arguments¶
id An integer that uniquely identifies the bridge group. Minimum value: 1 Maximum value: 1000
dynamicRouting Enable dynamic routing for this bridgegroup.
Possible values: ENABLED, DISABLED Default value: DISABLED
ipv6DynamicRouting Enable all IPv6 dynamic routing protocols on all VLANs bound to this bridgegroup. Note: For the ENABLED setting to work, you must configure IPv6 dynamic routing protocols from the VTYSH command line.
Possible values: ENABLED, DISABLED Default value: DISABLED
Example¶
add bridgegroup 1
show bridgegroup¶
Display the configured bridge group. If a name is specified, only that particular bridge group information is displayed. Otherwise, all configured bridge groups are displayed.
Synopsis¶
show bridgegroup [
Arguments¶
id The name of the bridge group. Minimum value: 1 Maximum value: 1000
Output¶
td Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0.
IPAddress The IP address assigned to the bridge group.
netmask The network mask for the subnet defined for the bridge group.
flags Temporary flag used for internal purpose.
portbitmap Member interfaces of this bridge group.
tagbitmap Tagged members of this bridge group.
ifaces Names of all member interfaces of this bridge group.
tagIfaces Names of all tagged member interfaces of this bridge group.
vlan Names of all member VLANs.
dynamicRouting Whether dynamic routing is enabled or disabled.
ipv6DynamicRouting Whether ipv6 dynamic routing is enabled or disabled.
rnat Temporary flag used for internal purpose.
flag partitionName Name of the Partition to which this vlan bound to.
ownerGroup The owner node group in a Cluster for this vlan.
devno count stateflag
Example¶
An example of the output of the show bridge group command is as follows: 2 configured Bridge Group: 1) Bridge Group: 1 Member vlans : 2 3 4 IP: 10.102.33.27 MASK: 255.255.255.0 2) Bridge Group: 2 Member vlans : 5 6