vrID6¶
The following operations can be performed on "vrID6":
bind| add| show| set| unset| unbind| rm|
bind vrID6¶
Binds the specified interfaces to a VMAC6 configuration.
Synopsis¶
bind vrID6
Arguments¶
id Integer value that uniquely identifies a VMAC6 address. Minimum value: 1 Maximum value: 255
ifnum Interfaces to bind to the VMAC. Use spaces to separate multiple entries. For a Citrix ADC, specify the interface in C/U notation (for example, 1/3).For a cluster setup for configuring interface based VRRP, specify the interface in N/C/U notation(for example, 2/1/3) . where C can take one of the following values:
* 0 - Indicates a mgmt port.
* 1 - Indicates a 1 Gbps port.
* 10 - Indicates a 10 Gbps port.
Note: Interface based VRRP is only applicable to a two-node cluster where one of node is in active state and the other in Spare. You must associate the VRID to the interfaces of both the nodes of the active-spare cluster setup. This is because unlike in a high availability setup, interface ID differs in a cluster setup.
trackifNum Interfaces which need to be tracked for this vrID.
Example¶
add vrID6 1
add vrID6¶
Adds a VMAC6 address to the Citrix ADC. A Virtual MAC address (VMAC6) is a floating entity, shared by the nodes in a high availability, or active-active, or cluster setup.
Synopsis¶
add vrID6
Arguments¶
id Integer value that uniquely identifies a VMAC6 address. Minimum value: 1 Maximum value: 255
priority Base priority (BP), in an active-active mode configuration, which ordinarily determines the master VIP address. Default value: 255 Minimum value: 0 Maximum value: 255
preemption In an active-active mode configuration, make a backup VIP address the master if its priority becomes higher than that of a master VIP address bound to this VMAC address. If you disable pre-emption while a backup VIP address is the master, the backup VIP address remains master until the original master VIP's priority becomes higher than that of the current master.
Possible values: ENABLED, DISABLED Default value: ENABLED
sharing In an active-active mode configuration, enable the backup VIP address to process any traffic instead of dropping it.
Possible values: ENABLED, DISABLED Default value: DISABLED
tracking The effective priority (EP) value, relative to the base priority (BP) value in an active-active mode configuration. When EP is set to a value other than None, it is EP, not BP, which determines the master VIP address. Available settings function as follows: * NONE - No tracking. EP = BP * ALL - If the status of all virtual servers is UP, EP = BP. Otherwise, EP = 0. * ONE - If the status of at least one virtual server is UP, EP = BP. Otherwise, EP = 0. * PROGRESSIVE - If the status of all virtual servers is UP, EP = BP. If the status of all virtual servers is DOWN, EP = 0. Otherwise EP = BP (1 - K/N), where N is the total number of virtual servers associated with the VIP address and K is the number of virtual servers for which the status is DOWN. Default: NONE.
Possible values: NONE, ONE, ALL, PROGRESSIVE Default value: NONE
preemptiondelaytimer Preemption delay time in seconds, in an active-active configuration. If any high priority node will come in network, it will wait for these many seconds before becoming master. Default value: 0 Minimum value: 1 Maximum value: 36000
trackifNumPriority Priority by which the Effective priority will be reduced if any of the tracked interfaces goes down in an active-active configuration. Default value: 0 Minimum value: 1 Maximum value: 255
ownerNode In a cluster setup, assign a cluster node as the owner of this VMAC address for IP based VRRP configuration. If no owner is configured, ow ner node is displayed as ALL and one node is dynamically elected as the owner. Default value: -1 Minimum value: 0 Maximum value: 31
Example¶
add vrID6 1
show vrID6¶
Displays the settings of all VRID6s configured on the Citrix ADC, or of the specified VRID6. To display the settings of all the VRID6s, run the command without any parameters. To display the settings of a particular VRID6, specify the VRID6.
Synopsis¶
show vrID6 [
Arguments¶
id Integer value that uniquely identifies a VMAC6 address. Minimum value: 1 Maximum value: 255
Output¶
ifaces Interfaces bound to this VRID.
ifnum Interfaces to bind to the VMAC6, specified in (slot/port) notation (for example, 1/2).Use spaces to separate multiple entries.
type Type (static or dynamic) of this VRID.
vlan The VLAN in which this VRID resides.
priority Base priority (BP), in an active-active mode configuration, which ordinarily determines the master VIP address.
state State of this VRID.
flags Flags.
stateflag IPAddress The IP address bound to the VRID6
preemption In an active-active mode configuration, make a backup VIP address the master if its priority becomes higher than that of a master VIP address bound to this VMAC address. If you disable pre-emption while a backup VIP address is the master, the backup VIP address remains master until the original master VIP's priority becomes higher than that of the current master.
sharing In an active-active mode configuration, enable the backup VIP address to process any traffic instead of dropping it.
preemptiondelaytimer Preemption delay time in seconds, in an active-active configuration. If any high priority node will come in network, it will wait for these many seconds before becoming master.
trackifNum Interfaces which need to be tracked for this vrID.
trackifNumPriority Priority by which the Effective priority will be reduced if any of the tracked interfaces goes down in an active-active configuration.
effectivePriority The effective priority of this VRID.
tracking The effective priority (EP) value, relative to the base priority (BP) value in an active-active mode configuration. When EP is set to a value other than None, it is EP, not BP, which determines the master VIP address. Available settings function as follows: * NONE - No tracking. EP = BP * ALL - If the status of all virtual servers is UP, EP = BP. Otherwise, EP = 0. * ONE - If the status of at least one virtual server is UP, EP = BP. Otherwise, EP = 0. * PROGRESSIVE - If the status of all virtual servers is UP, EP = BP. If the status of all virtual servers is DOWN, EP = 0. Otherwise EP = BP (1 - K/N), where N is the total number of virtual servers associated with the VIP address and K is the number of virtual servers for which the status is DOWN. Default: NONE.
operationalOwnerNode Run time owner node of the vrid.
ownerNode In a cluster setup, assign a cluster node as the owner of this VMAC address for IP based VRRP configuration. If no owner is configured, ow ner node is displayed as ALL and one node is dynamically elected as the owner.
devno count
Example¶
show vrid6
set vrID6¶
Modifies parameters related to a VMAC address on the Citrix ADC.
Synopsis¶
set vrID6
Arguments¶
id
Integer value that uniquely identifies the VMAC address. The generic VMACaddress is in the form of 00:00:5e:00:01:
priority Base priority (BP), in an active-active mode configuration, which ordinarily determines the master VIP address. Default value: 255 Minimum value: 0 Maximum value: 255
preemption In an active-active mode configuration, make a backup VIP address the master if its priority becomes higher than that of a master VIP address bound to this VMAC address. If you disable pre-emption while a backup VIP address is the master, the backup VIP address remains master until the original master VIP's priority becomes higher than that of the current master.
Possible values: ENABLED, DISABLED Default value: ENABLED
sharing In an active-active mode configuration, enable the backup VIP address to process any traffic instead of dropping it.
Possible values: ENABLED, DISABLED Default value: DISABLED
tracking The effective priority (EP) value, relative to the base priority (BP) value in an active-active mode configuration. When EP is set to a value other than None, it is EP, not BP, which determines the master VIP address. Available settings function as follows: * NONE - No tracking. EP = BP * ALL - If the status of all virtual servers is UP, EP = BP. Otherwise, EP = 0. * ONE - If the status of at least one virtual server is UP, EP = BP. Otherwise, EP = 0. * PROGRESSIVE - If the status of all virtual servers is UP, EP = BP. If the status of all virtual servers is DOWN, EP = 0. Otherwise EP = BP (1 - K/N), where N is the total number of virtual servers associated with the VIP address and K is the number of virtual servers for which the status is DOWN. Default: NONE.
Possible values: NONE, ONE, ALL, PROGRESSIVE Default value: NONE
preemptiondelaytimer Preemption delay time in seconds, in an active-active configuration. If any high priority node will come in network, it will wait for these many seconds before becoming master. Default value: 0 Minimum value: 1 Maximum value: 36000
trackifNumPriority Priority by which the Effective priority will be reduced if any of the tracked interfaces goes down in an active-active configuration. Default value: 0 Minimum value: 1 Maximum value: 255
ownerNode In a cluster setup, assign a cluster node as the owner of this VMAC address for IP based VRRP configuration. If no owner is configured, ow ner node is displayed as ALL and one node is dynamically elected as the owner. Default value: -1 Minimum value: 0 Maximum value: 31
Example¶
set vrID6 1 -priority 100
unset vrID6¶
Use this command to remove vrID6 settings.Refer to the set vrID6 command for meanings of the arguments.
Synopsis¶
unset vrID6
unbind vrID6¶
Unbinds the specified interfaces from a VMAC6 configuration.
Synopsis¶
unbind vrID6
Arguments¶
id Integer value that uniquely identifies a VMAC6 address. Minimum value: 1 Maximum value: 255
ifnum Interfaces to unbind from the VMAC6, specified in (slot/port) notation (for example, 1/2). Use spaces to separate multiple entries.
trackifNum Interfaces which need to be tracked for this vrID.
rm vrID6¶
Removes a specified VMAC6 entry or all VMAC6 entries from the Citrix ADC.
Synopsis¶
rm vrID6 (
Arguments¶
id Integer value that uniquely identifies a VMAC6 address. Minimum value: 1 Maximum value: 255
all Remove all configured VMAC6 addresses from the Citrix ADC.