Skip to content

L2Param

The following operations can be performed on "L2Param":

show| set| unset|

show L2Param

Displays the settings of global Layer 2 parameters on the Citrix ADC.

Synopsis

show L2Param

Arguments

Output

maxBridgeCollision Maximum bridge collision for loop detection

linkMTU this MTU is used for Ready logo purpose, changing the Interface MTU at soft layer level.

mbfPeermacUpdate When mbf_instant_learning is enabled, learn any changes in peer's MAC after this time interval, which is in 10ms ticks.

bdggrpProxyArp Set/reset proxy ARP in bridge group deployment

bdgSetting Bridging settings for C2C behavior. If enabled, each PE will learn MAC entries independently. Otherwise, when L2 mode is ON, learned MAC entries on a PE will be broadcasted to all other PEs.

garpOnVridIntf Send GARP messagess on VRID-configured interfaces upon failover

macModeFwdMyPkt Allows MAC mode vserver to pick and forward the packets even if it is destined to Citrix ADC owned VIP.

useMyMAC Use Citrix ADC MAC for all outgoing packets.

proxyArp Proxies the ARP as Citrix ADC MAC for FreeBSD.

garpReply Set/reset REPLY form of GARP

mbfInstLearning Enable instant learning of MAC changes in MBF mode.

rstIntfOnHaFo Enable the reset interface upon HA failover.

skipProxyingBsdTraffic Control source parameters (IP and Port) for FreeBSD initiated traffic. If Enabled, source parameters are retained. Else proxy the source parameters based on next hop.

returnToEthernetSender Return to ethernet sender.

stopMacMoveUpdate Stop Update of server mac change to NAT sessions.

bridgeAgeTimeout Time-out value for the bridge table entries, in seconds. The new value applies only to the entries that are dynamically learned after the new value is set. Previously existing bridge table entries expire after the previously configured time-out value.

useNetprofileBSDTraffic Control source parameters (IP and Port) for FreeBSD initiated traffic. If enabled proxy the source parameters based on netprofile source ip. If netprofile does not have ip configured, then it will continue to use NSIP as earlier.

set L2Param

Set Layer 2 related global settings on the Citrix ADC

Synopsis

set L2Param [-mbfPeermacUpdate ] [-maxBridgeCollision ] [-bdggrpProxyArp ( ENABLED | DISABLED )] [-bdgSetting ( ENABLED | DISABLED )] [-garpOnVridIntf ( ENABLED | DISABLED )] [-macModeFwdMyPkt ( ENABLED | DISABLED )] [-useMyMAC ( ENABLED | DISABLED )] [-proxyArp ( ENABLED | DISABLED )] [-garpReply ( ENABLED | DISABLED )] [-mbfInstLearning ( ENABLED | DISABLED )] [-rstIntfOnHaFo ( ENABLED | DISABLED )] [-skipProxyingBsdTraffic ( ENABLED | DISABLED )] [-returnToEthernetSender ( ENABLED | DISABLED )] [-stopMacMoveUpdate ( ENABLED | DISABLED )] [-bridgeAgeTimeout ] [-useNetprofileBSDTraffic ( ENABLED | DISABLED )]

Arguments

mbfPeermacUpdate When mbf_instant_learning is enabled, learn any changes in peer's MAC after this time interval, which is in 10ms ticks. Default value: 10 Minimum value: 0

maxBridgeCollision Maximum bridge collision for loop detection Default value: 20 Minimum value: 0

bdggrpProxyArp Set/reset proxy ARP in bridge group deployment

Possible values: ENABLED, DISABLED Default value: ENABLED

bdgSetting Bridging settings for C2C behavior. If enabled, each PE will learn MAC entries independently. Otherwise, when L2 mode is ON, learned MAC entries on a PE will be broadcasted to all other PEs.

Possible values: ENABLED, DISABLED Default value: DISABLED

garpOnVridIntf Send GARP messagess on VRID-configured interfaces upon failover

Possible values: ENABLED, DISABLED Default value: ENABLED

macModeFwdMyPkt Allows MAC mode vserver to pick and forward the packets even if it is destined to Citrix ADC owned VIP.

Possible values: ENABLED, DISABLED Default value: DISABLED

useMyMAC Use Citrix ADC MAC for all outgoing packets.

Possible values: ENABLED, DISABLED Default value: DISABLED

proxyArp Proxies the ARP as Citrix ADC MAC for FreeBSD.

Possible values: ENABLED, DISABLED Default value: ENABLED

garpReply Set/reset REPLY form of GARP

Possible values: ENABLED, DISABLED Default value: DISABLED

mbfInstLearning Enable instant learning of MAC changes in MBF mode.

Possible values: ENABLED, DISABLED Default value: DISABLED

rstIntfOnHaFo Enable the reset interface upon HA failover.

Possible values: ENABLED, DISABLED Default value: DISABLED

skipProxyingBsdTraffic Control source parameters (IP and Port) for FreeBSD initiated traffic. If Enabled, source parameters are retained. Else proxy the source parameters based on next hop.

Possible values: ENABLED, DISABLED Default value: DISABLED

returnToEthernetSender Return to ethernet sender.

Possible values: ENABLED, DISABLED Default value: DISABLED

stopMacMoveUpdate Stop Update of server mac change to NAT sessions.

Possible values: ENABLED, DISABLED Default value: DISABLED

bridgeAgeTimeout Time-out value for the bridge table entries, in seconds. The new value applies only to the entries that are dynamically learned after the new value is set. Previously existing bridge table entries expire after the previously configured time-out value. Default value: 300 Minimum value: 60 Maximum value: 300

useNetprofileBSDTraffic Control source parameters (IP and Port) for FreeBSD initiated traffic. If enabled proxy the source parameters based on netprofile source ip. If netprofile does not have ip configured, then it will continue to use NSIP as earlier.

Possible values: ENABLED, DISABLED Default value: DISABLED

unset L2Param

Use this command to remove L2Param settings.Refer to the set L2Param command for meanings of the arguments.

Synopsis

unset L2Param [-mbfPeermacUpdate] [-maxBridgeCollision] [-bdggrpProxyArp] [-bdgSetting] [-garpOnVridIntf] [-macModeFwdMyPkt] [-useMyMAC] [-proxyArp] [-garpReply] [-mbfInstLearning] [-rstIntfOnHaFo] [-skipProxyingBsdTraffic] [-returnToEthernetSender] [-stopMacMoveUpdate] [-bridgeAgeTimeout] [-useNetprofileBSDTraffic]

Was this article helpful?