Skip to content

channel

The following operations can be performed on "channel":

unset| rm| set| unbind| show| bind| add|

unset channel

Use this command to remove channel settings.Refer to the set channel command for meanings of the arguments.

Synopsis

unset channel [-state] [-speed] [-mtu] [-flowControl] [-haMonitor] [-haHeartbeat] [-tagall] [-ifAlias] [-throughput] [-lrMinThroughput] [-linkRedundancy] [-bandwidthHigh] [-bandwidthNormal]

rm channel

Removes an LA channel from the Citrix ADC or a cluster LA channel from a cluster configuration. Important: When a LA channel is removed, the network interfaces bound to it induce network loops that decrease network performance. You must disable the network interfaces before you remove the channel.

Synopsis

rm channel

Arguments

id ID of the LA channel or cluster LA channel or Link Redundant channel that you want to remove. Specify an LA channel in LA/x notation, where x can range from 1 to 8 or a cluster LA channel in CLA/x notation or Link redundant channel in LR/x notation , where x can range from 1 to 4.

set channel

Modifies the specified parameters of an LA channel.

Synopsis

set channel [-state ( ENABLED | DISABLED )] [-lamac ] [-speed ] [-mtu ] [-flowControl ] [-haMonitor ( ON | OFF )] [-haHeartbeat ( OFF | ON )] [-tagall ( ON | OFF )] [-ifAlias ] [-throughput ] [-lrMinThroughput ] [-linkRedundancy ( ON | OFF )] [-bandwidthHigh [-bandwidthNormal ]]

Arguments

id ID of the LA channel or the cluster LA channel whose parameters you want to modify. Specify an LA channel in LA/x notation, where x can range from 1 to 8 or a cluster LA channel in CLA/x notation or Link redundant channel in LR/x notation , where x can range from 1 to 4. Required for identifying the LA channel and cannot be modified.

state Enable or disable the LA channel.

Possible values: ENABLED, DISABLED Default value: ENABLED

lamac Allows User to set MAC address for LA channels on Hypervised platforms.

speed The speed for the LA channel.

Possible values: AUTO, 10, 100, 1000, 10000, 25000, 40000, 50000, 100000 Default value: AUTO

mtu The Maximum Transmission Unit (MTU) is the largest packet size, measured in bytes excluding 14 bytes ethernet header and 4 bytes CRC, that can be transmitted and received by an interface. The default value of MTU is 1500 on all the interface of Citrix ADC, some Cloud Platforms will restrict Citrix ADC to use the lesser default value. Any MTU value more than 1500 is called Jumbo MTU and will make the interface as jumbo enabled. The Maximum Jumbo MTU in Citrix ADC is 9216, however, some Virtualized / Cloud Platforms will have lesser Maximum Jumbo MTU Value (9000). In the case of Cluster, the Backplane interface requires an MTU value of 78 bytes more than the Max MTU configured on any other Data-Plane Interface. When the Data plane interfaces are all at default 1500 MTU, Cluster Back Plane will be automatically set to 1578 (1500 + 78) MTU. If a Backplane interface is reset to Data Plane Interface, then the 1578 MTU will be automatically reset to the default MTU of 1500(or whatever lesser default value). If any data plane interface of a Cluster is configured with a Jumbo MTU ( > 1500), then all backplane interfaces require to be configured with a minimum MTU of 'Highest Data Plane MTU in the Cluster + 78'. That makes the maximum Jumbo MTU for any Data-Plane Interface in a Cluster System to be '9138 (9216 - 78)., where 9216 is the maximum Jumbo MTU. On certain Virtualized / Cloud Platforms, the maximum possible MTU is restricted to a lesser value, Similar calculation can be applied, Maximum Data Plane MTU in Cluster = (Maximum possible MTU - 78). Default value: 1500 Minimum value: 1500 Maximum value: 9216

flowControl Required flow control for the LA channel.

Possible values: OFF, RX, TX, RXTX, ON Default value: OFF

haMonitor The state of HA monitoring for the LA channel.

Possible values: ON, OFF Default value: ON

haHeartbeat The state of HA HEARTBEAT SEND config for the LA channel.

Possible values: OFF, ON Default value: ON

tagall The appliance adds a four-byte 802.1q tag to every packet sent on this channel. ON applies tags for all the VLANs that are bound to this channel. OFF, applies the tag for all VLANs other than the native VLAN.

Possible values: ON, OFF Default value: OFF

ifAlias The alias name for the interface. Default value: " "

throughput Low threshold value for the throughput of the LA channel, in Mbps. In an high availability (HA) configuration, failover is triggered when the LA channel has HA MON enabled and the throughput is below the specified threshold. Minimum value: 0 Maximum value: 160000

lrMinThroughput Specifies the minimum throughput threshold (in Mbps) to be met by the active subchannel. Setting this parameter automatically divides an LACP channel into logical subchannels, with one subchannel active and the others in standby mode. When the maximum supported throughput of the active channel falls below the lrMinThroughput value, link failover occurs and a standby subchannel becomes active. Minimum value: 0 Maximum value: 80000

linkRedundancy Link Redundancy for Cluster LAG.

Possible values: ON, OFF Default value: OFF

bandwidthHigh High threshold value for the bandwidth usage of the LA channel, in Mbps. The Citrix ADC generates an SNMP trap message when the bandwidth usage of the LA channel is greater than or equal to the specified high threshold value. Minimum value: 0 Maximum value: 160000

bandwidthNormal Normal threshold value for the bandwidth usage of the LA channel, in Mbps. When the bandwidth usage of the LA channel returns to less than or equal to the specified normal threshold after exceeding the high threshold, the Citrix ADC generates an SNMP trap message to indicate that the bandwidth usage has returned to normal. Minimum value: 0 Maximum value: 160000

unbind channel

Unbinds the specified interfaces from an LA channel.

Synopsis

unbind channel ...

Arguments

id ID of the LA channel or cluster LA channel from which you want to unbind interfaces. Specify an LA channel in LA/x notation, where x can range from 1 to 8 or a cluster LA channel in CLA/x notation or Link redundant channel in LR/x notation , where x can range from 1 to 4.

ifnum Interfaces to be unbound from the LA channel of a Citrix ADC or from the LA channel of a cluster configuration. For an LA channel of a Citrix ADC, specify an interface in C/U notation (for example, 1/3). For an LA channel of a cluster configuration, specify an interface in N/C/U notation (for example, 2/1/3). where C can take one of the following values: * 0 - Indicates a management interface. * 1 - Indicates a 1 Gbps port. * 10 - Indicates a 10 Gbps port. U is a unique integer for representing an interface in a particular port group. N is the ID of the node to which an interface belongs in a cluster configuration. Use spaces to separate multiple entries.

show channel

Displays the settings of all LA channels or of the specified channel. To display the settings of all channels, run the command without any parameters. To display the settings of a particular channel, specify the ID of the channel.

Synopsis

show channel []

Arguments

id ID of an LA channel or LA channel in cluster configuration whose details you want the Citrix ADC to display. Specify an LA channel in LA/x notation, where x can range from 1 to 8 or a cluster LA channel in CLA/x notation or Link redundant channel in LR/x notation , where x can range from 1 to 4. Minimum value: 1

Output

stateflag deviceName LA channel name in form LA/x, where x is channel ID, which ranges from 1 to 8 or LR channel name in form LR/x, where x is channel ID, which ranges from 1 to 4

unit Unit number of the channel. This is an internal reference number that the Citrix ADC uses to identify the channel.

description The IEEE standard that the channel is based on.

flags Flags of this channel.

mtu The Maximum Transmission Unit (MTU) is the largest packet size, measured in bytes excluding 14 bytes ethernet header and 4 bytes CRC, that can be transmitted and received by an interface. The default value of MTU is 1500 on all the interface of Citrix ADC, some Cloud Platforms will restrict Citrix ADC to use the lesser default value. Any MTU value more than 1500 is called Jumbo MTU and will make the interface as jumbo enabled. The Maximum Jumbo MTU in Citrix ADC is 9216, however, some Virtualized / Cloud Platforms will have lesser Maximum Jumbo MTU Value (9000). In the case of Cluster, the Backplane interface requires an MTU value of 78 bytes more than the Max MTU configured on any other Data-Plane Interface. When the Data plane interfaces are all at default 1500 MTU, Cluster Back Plane will be automatically set to 1578 (1500 + 78) MTU. If a Backplane interface is reset to Data Plane Interface, then the 1578 MTU will be automatically reset to the default MTU of 1500(or whatever lesser default value). If any data plane interface of a Cluster is configured with a Jumbo MTU ( > 1500), then all backplane interfaces require to be configured with a minimum MTU of 'Highest Data Plane MTU in the Cluster + 78'. That makes the maximum Jumbo MTU for any Data-Plane Interface in a Cluster System to be '9138 (9216 - 78)., where 9216 is the maximum Jumbo MTU. On certain Virtualized / Cloud Platforms, the maximum possible MTU is restricted to a lesser value, Similar calculation can be applied, Maximum Data Plane MTU in Cluster = (Maximum possible MTU - 78).

actualMtu MTU of the channel. This is the maximum frame size that the channel can process.

vlan Native VLAN of the channel.

mac MAC address of the channel.

lamac Specifies a MAC address for the LA channels configured in Citrix ADC virtual appliances (VPX). This MAC address is persistent after each reboot. If you don't specify this parameter, a MAC address is generated randomly for each LA channel. These MAC addresses change after each reboot.

uptime Duration for which the channel is UP. (Example: 3 hours 1 minute 1 second). This value is reset when the channel state changes to DOWN.

downTime Duration for which the channel is DOWN. (Example: 3 hours 1 minute 1 second). This value is reset when the channel state changes to UP.

reqMedia Requested media setting for this channel. Since there is no media associated with LA, the displayed values carry no significance.

reqSpeed Requested speed setting for this channel. Since no media are associated with LA, this speed is used to determine the threshold for the slave interfaces. If the speed of the member interface is less than the requested speed, that interface is considered inactive.

reqDuplex Requested duplex setting for this channel. Since no media are associated with LA, the displayed values carry no significance.

reqFlowcontrol Requested flow control setting for this channel. Since no media are associated with LA, the displayed values carry no significance.

media Actual media setting for this channel.

speed Ethernet speed of the channel, in Mbps. If the speed of any bound interface is greater than or equal to the value set for this parameter, the state of the interface is UP. Otherwise, the state is INACTIVE. Bound Interfaces whose state is INACTIVE do not process any traffic.

duplex Actual duplex setting for this channel.

flowControl Specifies the flow control type for this LA channel to manage the flow of frames. Flow control is a function as mentioned in clause 31 of the IEEE 802.3 standard. Flow control allows congested ports to pause traffic from the peer device. Flow control is achieved by sending PAUSE frames.

media Requested media setting for this interface.

speed Actual speed setting for this channel.

duplex Actualduplex setting for this interface.

flowControl Actual flow control setting for this channel.

Mode The type of LA: static LA or dynamic LA (LACP). Possible values: Manual, AUTO. Manual shows the static LA, and AUTO shows the LACP.

Mode The mode(AUTO/MANNUAL) for the LA channel.

haMonitor HA monitoring enabled or disabled for this channel.

haHeartbeat The state of HA HEARTBEAT SEND for the LA channel.

state Enable or disable the LA channel.

autoneg Requested auto negotiation setting for this channel. Since no media are associated with LA, this setting has no effect.

autonegResult Actual auto negotiation setting for this channel.

tagged VLAN tags setting on this channel.

tagall The appliance adds a four-byte 802.1q tag to every packet sent on this channel. ON applies tags for all the VLANs that are bound to this channel. OFF, applies the tag for all VLANs other than the native VLAN.

trunk This is deprecated by tagall

taggedAny Channel setting to accept/drop all tagged packets.

taggedAutolearn Dynaminc vlan membership on this channel.

hangDetect Hang detect for this channel.

hangReset Hang reset for this channel.

linkState The current state of the link associated with the interface. For logical interfaces (LA), the state of the link is dependent on the state of the slave interfaces. For the link to be UP at least one of the slave interfaces needs to be UP.

intfState Current state of the specified interface. The interface state set to UP only if the link state is UP and administrative state is ENABLED.

rxpackets Number of bytes received by all the slave interfaces of the channel since the Citrix ADC was started or the interface statistics were cleared.

rxbytes Number of packets received by all member interfaces since the Citrix ADC was started or the interface statistics were cleared.

rxerrors Number of inbound packets dropped by the hardware of the slave interfaces since the Citrix ADC was started or the interface statistics were cleared. Possible causes of dropped packets are CRC, length (undersize or oversize), and alignment errors.

rxdrops Number of inbound packets dropped by the channel's slave interfaces. Commonly dropped packets are multicast frames, spanning tree BPDUs, packets destined to a MAC not owned by the Citrix ADC when L2 mode is disabled, or packets tagged for a VLAN that is not bound to the interface. In most healthy networks, this statistic increments at a steady rate regardless of traffic load. A sharp spike in dropped packets generally indicates an issue with connected L2 switches, such as a forwarding database overflow resulting in packets being broadcast on all ports.

txpackets Number of packets transmitted by slave interfaces of a channel since the Citrix ADC was started or the interface statistics were cleared.

txbytes Number of bytes transmitted by slave interfaces of a channel since the Citrix ADC was started or the interface statistics were cleared.

txerrors Number of outbound packets dropped by the hardware of a channel's slave interfaces since the Citrix ADC was started or the interface statistics were cleared. Possible causes of dropped packets are length (undersize or oversize) errors and lack of resources.

txdrops Number of packets dropped in transmission by a channel's slave interfaces for one of the following reasons: (1) VLAN mismatch. (2) Oversized packets. (3) Interface congestion. (4) Loopback packets sent on non-loopback interface.

inDisc Number of error-free inbound packets discarded by a channel's slave interfaces because of a lack of resources (for example, insufficient receive buffers).

outDisc Number of error-free outbound packets discarded by a channel's slave interfaces because of a lack of resources. This statistic is not available on: (1) 10G ports of Citrix ADC MPX 12500/12500/15500-10G platforms. (2) 10G data ports on Citrix ADC MPX 17500/19500/21500 platforms.

fctls Number of times flow control is performed on a channel's slave interfaces because of pause frames.

hangs Number of hangs that occurred on the channel's slave interfaces.

stsStalls Number of status stalls that occurred on the channel's slave interfaces.

txStalls Number of Tx stalls happened that occurred on the channel's slave interfaces.

rxStalls Number of Rx stalls that occurred on the channel's slave interfaces.

bdgMuted Number of times a channel's slave interfaces stopped transmitting and receiving packets because of MAC moves between ports.

vmac Virtual MAC of this channel.

vmac6 Virtual MAC for IPv6 on this interface.

ifAlias The alias name for the interface.

reqThroughput Minimum required throughput for an interface. Failover is triggered if the operating throughput of a Link Aggregation (LA) channel for which HAMON is ON falls below this value.

lrMinThroughput Specifies the minimum throughput threshold (in Mbps) to be met by the active subchannel. Setting this parameter automatically divides an LACP channel into logical subchannels, with one subchannel active and the others in standby mode. When the maximum supported throughput of the active channel falls below the lrMinThroughput value, link failover occurs and a standby subchannel becomes active.

linkRedundancy Link Redundancy for Cluster LAG.

throughput Low threshold value for the throughput of the LA channel, in Mbps. In an high availability (HA) configuration, failover is triggered when the LA channel has HA MON enabled and the throughput is below the specified threshold.

throughput Actual throughput for the interface.

bandwidthHigh High threshold value for the bandwidth usage of the LA channel, in Mbps. The Citrix ADC generates an SNMP trap message when the bandwidth usage of the LA channel is greater than or equal to the specified high threshold value.

bandwidthNormal Normal threshold value for the bandwidth usage of the LA channel, in Mbps. When the bandwidth usage of the LA channel returns to less than or equal to the specified normal threshold after exceeding the high threshold, the Citrix ADC generates an SNMP trap message to indicate that the bandwidth usage has returned to normal.

ifnum The interfaces bound to link aggregate channel.

backplane The cluster backplane status of the LA. If the status is enabled, the LA is part of the cluster backplane. By default, the backplane status is disabled.

clearTime Time since the interface stats are cleared last time.

slavestate State of the member interfaces.

slavemedia Media type of the member interfaces.

slavespeed Speed of the member interfaces.

slaveduplex Duplex of the member interfaces.

slaveflowctl Flowcontrol of the member interfaces.

slavetime UP time of the member interfaces.

lacpMode The LACP mode of the specified interface. The possible values are: 1. Active: A port in active mode generates LACP protocol messages on a regular basis, regardless of any need expressed by its partner to receive them. 2. Passive: A port in passive mode generally does not transmit LACP messages unless its partner is in the active mode; that is, it does not speak unless spoken to. 3. Disabled: Removes the interface from the LA channel. If this is only interface in the LA channel, the LA channel is also deleted.

lacpTimeout Time to wait for the LACPDU. If a LACPDU is not received within this interval, the Citrix ADC markes the link partner port as DOWN. Possible values: Long and Short. Long lacptimeout is 90 sec and Short LACP timeout is 3 sec.

lacpActorPriority LACP Actor Priority. A LACP port priority is configured on each port using LACP. LACP uses the port priority with the port number to form the port identifier. The port priority determines which ports should be put in standby mode when there is a hardware limitation that prevents all compatible ports from aggregating.

lacpActorPortno LACP Actor port number. LACP uses the port priority with the port number to form the port identifier.

lacpPartnerState LACP Partner State. Whether the port is in Active or Passive negotiating state.

lacpPartnerTimeout The timeout value for the information revieved in LACPDUs. It can have values as SHORT or LONG. The SHORT timeout is 3s and the LONG timeout is 90s.

lacpPartnerAggregation The Aggregation flag indicates that the participant will allow the link to be used as part of an aggregate. Otherwise the link is to be used as an individual link, i.e. not aggregated with any other.

lacpPartnerInsync The Synchronization flag indicates that the transmitting participant.s mux component is in sync with the system id and key information transmitted.

lacpPartnerCollecting The Collecting flag indicates that the participant.s collector, i.e. the reception component of the mux, is definitely on. If set the flag communicates collecting.

lacpPartnerDistributing The Distributing flag indicates that the participant.s distributor is not definitely off. If reset the flag indicates not distributing.

lacpPartnerDefaulted If the timer expires in the Expired state, the Receive Machine enters the Defaulted state.

lacpPartnerExpired If the LACPDUs are received for timeout period, the Receive Machine enters the Expired state and the timer is restarted with the timeout value of SHORT timeout

lacpPartnerPriority LACP Partner Priority. A LACP port priority is configured on each port using LACP. LACP uses the port priority with the port number to form the port identifier. The port priority determines which ports should be put in standby mode when there is a hardware limitation that prevents all compatible ports from aggregating.

lacpPartnerSystemMac LACP Partner System MAC.

lacpPartnerSystemPriority LACP Partner System Priority. The LACP partner's system priority. The values for the priority range from 0 to 65535. The lower the value, the higher the system priority. The switch with the lower system priority value determines which links between LACP partner are active and which are in the standby for each LACP Channel.

lacpPartnerPortno LACP Partner Port number. LACP uses the port priority with the port number to form the port identifier.

lacpPartnerKey LACP Partner Key. The LACP key used by the partner port.

lacpActorAggregation The Aggregation flag indicates that the participant will allow the link to be used as part of an aggregate. Otherwise the link is to be used as an individual link, i.e. not aggregated with any other.

lacpActorInsync The Synchronization flag indicates that the transmitting participant.s mux component is in sync with the system id and key information transmitted.

lacpActorCollecting The Collecting flag indicates that the participant.s collector, i.e. the reception component of the mux, is definitely on. If set the flag communicates collecting.

lacpActorDistributing The Distributing flag indicates that the participant.s distributor is not definitely off. If reset the flag indicates not distributing.

lacpPortMuxState LACP Port MUX state. The state of the MUX control machine. The Mux Control Machine attaches the physical port to an aggregate port, using the Selection Logic to choose an appropriate port, and turns the distributor and collector for the physical port on or off as required by protocolinformation.

lacpPortRxStat LACP Port RX state. The state of the Receive machine. The Receive Machine maintains partner information, recording protocol information from LACPDUs sent by remote partner(s). Received information is subject to a timeout, and if sufficient time elapses the receive machine will revert to using default partner information.

lacpPortSelectState LACP Port SELECT state. The state of the SELECT state machine, It could be SELECTED or UNSELECTED.

lldpmode Link Layer Discovery Protocol (LLDP) mode for an interface. The resultant LLDP mode of an interface depends on the LLDP mode configured at the global and the interface levels.

svmCmd New attribute added to identify the source of cmd, when SVM fires the nitro cmd, it will set the value of SVMCMD to be 1.

lrActiveIntf LR set member interface state(active/inactive).

devno count

bind channel

Binds the specified interfaces to a channel.

Synopsis

bind channel ...

Arguments

id ID of the LA channel or the cluster LA channel to which you want to bind interfaces. Specify an LA channel in LA/x notation, where x can range from 1 to 8 or a cluster LA channel in CLA/x notation or Link redundant channel in LR/x notation , where x can range from 1 to 4.

ifnum Interfaces to be bound to the LA channel of a Citrix ADC or to the LA channel of a cluster configuration.

In case of standalone or HA configuration, Maximum 16 interfaces can be bound to a channel. In case of Cluster configuration, Maximum 16 interfaces can be bound to a Node level channel and maximum 16 interafce from each node can be bound to a Cluster level channel.

For an LA channel of a Citrix ADC, specify an interface in C/U notation (for example, 1/3). For an LA channel of a cluster configuration, specify an interface in N/C/U notation (for example, 2/1/3). where C can take one of the following values: * 0 - Indicates a management interface. * 1 - Indicates a 1 Gbps port. * 10 - Indicates a 10 Gbps port. * 40 - Indicates a 40 Gbps port. U is a unique integer for representing an interface in a particular port group. N is the ID of the node to which an interface belongs in a cluster configuration. Use spaces to separate multiple entries.

add channel

Creates a link aggregate channel on the Citrix ADC or on a cluster configuration. Link aggregation combines data coming from multiple ports into a single high-speed link. Configuring link aggregation increases the capacity and availability of the communication channel between the Citrix ADC appliance and other connected devices. When a network interface is bound to a channel, the channel parameters have precedence over the network interface parameters. That is, the network interface parameters are ignored. A network interface can be bound only to one channel.

Synopsis

add channel [-ifnum ...] [-state ( ENABLED | DISABLED )] [-lamac ] [-speed ] [-flowControl ] [-haMonitor ( ON | OFF )] [-haHeartbeat ( OFF | ON )] [-tagall ( ON | OFF )] [-ifAlias ] [-throughput ] [-bandwidthHigh [-bandwidthNormal ]]

Arguments

id ID for the LA channel or cluster LA channel or LR channel to be created. Specify an LA channel in LA/x notation, where x can range from 1 to 8 or cluster LA channel in CLA/x notation or Link redundant channel in LR/x notation, where x can range from 1 to 4. Cannot be changed after the LA channel is created.

ifnum Interfaces to be bound to the LA channel of a Citrix ADC or to the LA channel of a cluster configuration. For an LA channel of a Citrix ADC, specify an interface in C/U notation (for example, 1/3). For an LA channel of a cluster configuration, specify an interface in N/C/U notation (for example, 2/1/3). where C can take one of the following values: * 0 - Indicates a management interface. * 1 - Indicates a 1 Gbps port. * 10 - Indicates a 10 Gbps port. U is a unique integer for representing an interface in a particular port group. N is the ID of the node to which an interface belongs in a cluster configuration. Use spaces to separate multiple entries.

state Enable or disable the LA channel.

Possible values: ENABLED, DISABLED Default value: ENABLED

lamac Specifies a MAC address for the LA channels configured in Citrix ADC virtual appliances (VPX). This MAC address is persistent after each reboot. If you don't specify this parameter, a MAC address is generated randomly for each LA channel. These MAC addresses change after each reboot.

speed Ethernet speed of the channel, in Mbps. If the speed of any bound interface is greater than or equal to the value set for this parameter, the state of the interface is UP. Otherwise, the state is INACTIVE. Bound Interfaces whose state is INACTIVE do not process any traffic.

Possible values: AUTO, 10, 100, 1000, 10000, 25000, 40000, 50000, 100000 Default value: AUTO

flowControl Specifies the flow control type for this LA channel to manage the flow of frames. Flow control is a function as mentioned in clause 31 of the IEEE 802.3 standard. Flow control allows congested ports to pause traffic from the peer device. Flow control is achieved by sending PAUSE frames.

Possible values: OFF, RX, TX, RXTX, ON Default value: OFF

haMonitor In a High Availability (HA) configuration, monitor the LA channel for failure events. Failure of any LA channel that has HA MON enabled triggers HA failover.

Possible values: ON, OFF Default value: ON

haHeartbeat In a High Availability (HA) configuration, configure the LA channel for sending heartbeats. LA channel that has HA Heartbeat disabled should not send the heartbeats.

Possible values: OFF, ON Default value: ON

tagall Adds a four-byte 802.1q tag to every packet sent on this channel. The ON setting applies tags for all VLANs that are bound to this channel. OFF applies the tag for all VLANs other than the native VLAN.

Possible values: ON, OFF Default value: OFF

ifAlias Alias name for the LA channel. Used only to enhance readability. To perform any operations, you have to specify the LA channel ID. Default value: " "

throughput Low threshold value for the throughput of the LA channel, in Mbps. In an high availability (HA) configuration, failover is triggered when the LA channel has HA MON enabled and the throughput is below the specified threshold. Minimum value: 0 Maximum value: 160000

bandwidthHigh High threshold value for the bandwidth usage of the LA channel, in Mbps. The Citrix ADC generates an SNMP trap message when the bandwidth usage of the LA channel is greater than or equal to the specified high threshold value. Minimum value: 0 Maximum value: 160000

bandwidthNormal Normal threshold value for the bandwidth usage of the LA channel, in Mbps. When the bandwidth usage of the LA channel returns to less than or equal to the specified normal threshold after exceeding the high threshold, the Citrix ADC generates an SNMP trap message to indicate that the bandwidth usage has returned to normal. Minimum value: 0 Maximum value: 160000

Was this article helpful?