ADC NITRO APIs

l3param

Configuration for Layer 3 related parameter resource.

Properties

(click to see Operations )

Name Data Type Permissions Description
srcnat <String> Read-write Perform NAT if only the source is in the private network.

Default value: ENABLED

Possible values = ENABLED, DISABLED
icmpgenratethreshold <Double> Read-write NS generated ICMP pkts per 10ms rate threshold.

Default value: 100
overridernat <String> Read-write USNIP/USIP settings override RNAT settings for configured

service/virtual server traffic.. .

Default value: DISABLED

Possible values = ENABLED, DISABLED
dropdfflag <String> Read-write Enable dropping the IP DF flag.

Default value: DISABLED

Possible values = ENABLED, DISABLED
miproundrobin <String> Read-write Enable round robin usage of mapped IPs.

Default value: ENABLED

Possible values = ENABLED, DISABLED
externalloopback <String> Read-write Enable external loopback.

Default value: DISABLED

Possible values = ENABLED, DISABLED
tnlpmtuwoconn <String> Read-write Enable/Disable learning PMTU of IP tunnel when ICMP error does not contain connection information.

Default value: ENABLED

Possible values = ENABLED, DISABLED
usipserverstraypkt <String> Read-write Enable detection of stray server side pkts in USIP mode.

Default value: DISABLED

Possible values = ENABLED, DISABLED
forwardicmpfragments <String> Read-write Enable forwarding of ICMP fragments.

Default value: DISABLED

Possible values = ENABLED, DISABLED
dropipfragments <String> Read-write Enable dropping of IP fragments.

Default value: DISABLED

Possible values = ENABLED, DISABLED
acllogtime <Double> Read-write Parameter to tune acl logging time.

Default value: 5000
implicitaclallow <String> Read-write Do not apply ACLs for internal ports.

Default value: ENABLED

Possible values = ENABLED, DISABLED
dynamicrouting <String> Read-write Enable/Disable Dynamic routing on partition. This configuration is not applicable to default partition.

Default value: DISABLED

Possible values = ENABLED, DISABLED
ipv6dynamicrouting <String> Read-write Enable/Disable IPv6 Dynamic routing.

Default value: DISABLED

Possible values = ENABLED, DISABLED
allowclasseipv4 <String> Read-write Enable/Disable IPv4 Class E address clients.

Default value: DISABLED

Possible values = ENABLED, DISABLED

Operations

(click to see Properties )

  • UPDATE
  • UNSET
  • GET (ALL)

Some options that you can use for each operations:

  • Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

    http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes

    If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.

  • Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

    To do this, you must specify the username and password in the request header of the NITRO request as follows:

    X-NITRO-USER: <username>

    X-NITRO-PASS: <password>

    Note: In such cases, make sure that the request header DOES not include the following:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

*Note: * Mandatory parameters are marked in red and placeholder content is marked in green

update

URL: http:// <netscaler-ip-address> /nitro/v1/config/l3param HTTP Method: PUT

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"l3param":{
"srcnat":<String_value>,
"icmpgenratethreshold":<Double_value>,
"overridernat":<String_value>,
"dropdfflag":<String_value>,
"miproundrobin":<String_value>,
"externalloopback":<String_value>,
"tnlpmtuwoconn":<String_value>,
"usipserverstraypkt":<String_value>,
"forwardicmpfragments":<String_value>,
"dropipfragments":<String_value>,
"acllogtime":<Double_value>,
"implicitaclallow":<String_value>,
"dynamicrouting":<String_value>,
"ipv6dynamicrouting":<String_value>,
"allowclasseipv4":<String_value>
}}

<!--NeedCopy-->

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

unset

URL: http:// <netscaler-ip-address> /nitro/v1/config/l3param? action=unset HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"l3param":{
"srcnat":true,
"icmpgenratethreshold":true,
"overridernat":true,
"dropdfflag":true,
"miproundrobin":true,
"externalloopback":true,
"tnlpmtuwoconn":true,
"usipserverstraypkt":true,
"forwardicmpfragments":true,
"dropipfragments":true,
"acllogtime":true,
"implicitaclallow":true,
"dynamicrouting":true,
"ipv6dynamicrouting":true,
"allowclasseipv4":true
}}

<!--NeedCopy-->

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

get (all)

URL: http:// <netscaler-ip-address> /nitro/v1/config/l3param HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "l3param": [ {
"srcnat":<String_value>,
"icmpgenratethreshold":<Double_value>,
"overridernat":<String_value>,
"dropdfflag":<String_value>,
"miproundrobin":<String_value>,
"externalloopback":<String_value>,
"tnlpmtuwoconn":<String_value>,
"usipserverstraypkt":<String_value>,
"forwardicmpfragments":<String_value>,
"dropipfragments":<String_value>,
"acllogtime":<Double_value>,
"implicitaclallow":<String_value>,
"dynamicrouting":<String_value>,
"ipv6dynamicrouting":<String_value>,
"allowclasseipv4":<String_value>
}]}

<!--NeedCopy-->
l3param