Skip to content
Was this article helpful?


Configuration for ADC Capacity Utilization resource.


(click to see Operations )

Name Data Type Permissions Description
allnic_err_rl_rate_pkt_drops <Double> Read-write allnic_err_rl_rate_pkt_drops Value .
allnic_err_rl_pps_pkt_drops <Double> Read-write allnic_err_rl_pps_pkt_drops Value .
allnic_err_rl_cpu_pkt_drops <Double> Read-write allnic_err_rl_cpu_pkt_drops Value .
report_level <Integer> Read-write whether the row is for minutely, hourly etc.
device_ip_address <String> Read-write Device IP Address.

Minimum length = 1

Maximum length = 64
rl_tot_ssl_rl_data_limited <Double> Read-write rl_tot_ssl_rl_data_limited Value .
timestamp <Double> Read-write timestamp in milliseconds.
allnic_err_rl_pkt_drops <Double> Read-write allnic_err_rl_pkt_drops Value.
rl_tot_ssl_rl_sess_limited <Double> Read-write rl_tot_ssl_rl_sess_limited Value .
rl_tot_ssl_rl_enforced <Double> Read-write rl_tot_ssl_rl_enforced Value .
id <String> Read-write Id is system generated key for all the entries in this perf table configuration.

Maximum length = 256
agg_level <Integer> Read-write whether the row is Aggregated for Avg, Min, Max etc.
report_start_time <Double> Read-write report_start_time in seconds.
report_end_time <Double> Read-write report_end_time in seconds.


(click to see Properties )

  • GET (ALL)

Some options that you can use for each operations:

  • Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

    http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes

    If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.

  • Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

    To do this, you must specify the username and password in the request header of the NITRO request as follows:

    X-NITRO-USER: <username>

    X-NITRO-PASS: <password>

    Note: In such cases, make sure that the request header DOES not include the following:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Note: Mandatory parameters are marked in red and placeholder content is marked in green

The following parameters can be used in the nitro request : onerror <String_value>

Use this parameter to set the onerror status for nitro request. Applicable only for bulk requests.

Default value: EXIT

Possible values = EXIT, CONTINUE

get (all)

URL: https://<MGMT-IP>/nitro/v2/config/perf_capacity_utilization_report Query-parameters:

filter https://<MGMT-IP>/nitro/v2/config/perf_capacity_utilization_report ?filter=property-name1:property-value1,property-name2:property-value2 Use this query-parameter to get the filtered set of perf_capacity_utilization_report resources configured on the system. You can set a filter on any property of the resource.

pagesize=#no;pageno=#no https://<MGMT-IP>/nitro/v2/config/perf_capacity_utilization_report ?pagesize=#no;pageno=#no Use this query-parameter to get the perf_capacity_utilization_report resources in chunks.

count https://<MGMT-IP>/nitro/v2/config/perf_capacity_utilization_report ?count=yes Use this query-parameter to get the count of perf_capacity_utilization_report resources.


Request Headers: Accept: application/json





Response: HTTPS Status Code on Success: 200 OK HTTPS Status Code on Failure: 4xx (for general HTTPS errors) or 5xx (for NetScaler-MAS-specific errors). The response payload provides details of the error

Response Headers:


Response Payload:

{ "errorcode": 0, "message": "Done", "severity": ;ltString_value;gt, "perf_capacity_utilization_report":[{
Was this article helpful?