Skip to content
Was this article helpful?

perf_device_counters

Configuration for Device Counter Table resource.

Properties

(click to see Operations )

Name Data Type Permissions Description
device_family <String> Read-write Device Family of which the counter belongs to.
counter_group <String> Read-write Counter Group of which the counter belongs to.

Minimum length = 1

Maximum length = 100
is_tabular <Boolean> Read-write Is Tabular.
min_ver_supported <String> Read-write Minimum Version supported by the counter Group.

Minimum length = 1

Maximum length = 100
counter_name <String> Read-write Counter Name.

Minimum length = 1

Operations

(click to see Properties )

  • GET (ALL)

Some options that you can use for each operations:

  • Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

    http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes

    If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.

  • Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

    To do this, you must specify the username and password in the request header of the NITRO request as follows:

    X-NITRO-USER: <username>

    X-NITRO-PASS: <password>

    Note: In such cases, make sure that the request header DOES not include the following:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Note:

Mandatory parameters are marked in red and placeholder content is marked in green

The following parameters can be used in the nitro request : onerror <String_value>

Use this parameter to set the onerror status for nitro request. Applicable only for bulk requests.

Default value: EXIT

Possible values = EXIT, CONTINUE

get (all)

URL: https://<MGMT-IP>/nitro/v2/config/perf_device_counters

Query-parameters:

filter https://<MGMT-IP>/nitro/v2/config/perf_device_counters ?filter=property-name1:property-value1,property-name2:property-value2

Use this query-parameter to get the filtered set of perf_device_counters resources configured on the system. You can set a filter on any property of the resource.

pagesize=#no;pageno=#no https://<MGMT-IP>/nitro/v2/config/perf_device_counters ?pagesize=#no;pageno=#no

Use this query-parameter to get the perf_device_counters resources in chunks.

count https://<MGMT-IP>/nitro/v2/config/perf_device_counters ?count=yes

Use this query-parameter to get the count of perf_device_counters resources.

HTTPS Method: GET

Request Headers:

Accept: application/json

X-NITRO-USER:username_value<String>

X-NITRO-PASS:password_value<String>

or

Cookie:NITRO_AUTH_TOKEN=token_value<String>

Response:

HTTPS Status Code on Success: 200 OK HTTPS Status Code on Failure: 4xx (for general HTTPS errors) or 5xx (for NetScaler-MAS-specific errors). The response payload provides details of the error

Response Headers:

Content-Type:application/json

Response Payload:

{ "errorcode": 0, "message": "Done", "severity": ;ltString_value;gt, "perf_device_counters":[{
      "device_family":<String_value>,
      "counter_group":<String_value>,
      "is_tabular":<Boolean_value>,
      "min_ver_supported":<String_value>,
      "counter_name":<String_value>}]}
Was this article helpful?