Skip to content
Was this article helpful?


Configuration for SSL Back-end Ciphers report resource.


(click to see Operations )

Name Data Type Permissions Description
sslbkendcipheraes256rate <Double> Read-write sslbkendcipheraes256rate Value .
sslbe40bitdesciphersrate <Double> Read-write sslbe40bitdesciphersrate Value .
sslbe56bitdesciphersrate <Double> Read-write sslbe56bitdesciphersrate Value .
sslbe168bit3desciphersrate <Double> Read-write sslbe168bit3desciphersrate Value .
sslbe40bitrc2ciphersrate <Double> Read-write sslbe40bitrc2ciphersrate Value .
timestamp <Double> Read-write timestamp in milliseconds.
id <String> Read-write Id is system generated key for all the entries in this perf table configuration.

Maximum length = 256
sslbe128bitrc4ciphersrate <Double> Read-write sslbe128bitrc4ciphersrate Value .
agg_level <Integer> Read-write whether the row is Aggregated for Avg, Min, Max etc.
sslbenullciphersrate <Double> Read-write sslbenullciphersrate Value .
sslbe64bitrc4ciphersrate <Double> Read-write sslbe64bitrc4ciphersrate Value .
sslbe56bitrc2ciphersrate <Double> Read-write sslbe56bitrc2ciphersrate Value .
sslbe40bitrc4ciphersrate <Double> Read-write sslbe40bitrc4ciphersrate Value.
report_level <Integer> Read-write whether the row is for minutely, hourly etc.
device_ip_address <String> Read-write Device IP Address.

Minimum length = 1

Maximum length = 64
sslbe128bitrc2ciphersrate <Double> Read-write sslbe128bitrc2ciphersrate Value .
sslbkendcipheraes128rate <Double> Read-write sslbkendcipheraes128rate Value .
sslbe56bitrc4ciphersrate <Double> Read-write sslbe56bitrc4ciphersrate Value .
report_start_time <Double> Read-write report_start_time in seconds.
report_end_time <Double> Read-write report_end_time in seconds.


(click to see Properties )

  • GET

Some options that you can use for each operations:

  • Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

    http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes

    If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.

  • Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

    To do this, you must specify the username and password in the request header of the NITRO request as follows:

    X-NITRO-USER: <username>

    X-NITRO-PASS: <password>

    Note: In such cases, make sure that the request header DOES not include the following:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Note: Mandatory parameters are marked in red and placeholder content is marked in green

The following parameters can be used in the nitro request : onerror <String_value>

Use this parameter to set the onerror status for nitro request. Applicable only for bulk requests.

Default value: EXIT

Possible values = EXIT, CONTINUE


URL: https://<MGMT-IP>/nitro/v2/config/perf_ssl_backend_ciphers_report HTTPS Method: GET

Request Headers: Accept: application/json





Response: HTTPS Status Code on Success: 200 OK HTTPS Status Code on Failure: 4xx (for general HTTPS errors) or 5xx (for NetScaler-MAS-specific errors). The response payload provides details of the error

Response Headers:


Response Payload:

{ "errorcode": 0, "message": "Done", "severity": ;ltString_value;gt, "perf_ssl_backend_ciphers_report":[{
Was this article helpful?