Skip to content

L2Param

The following operations can be performed on "L2Param":

set | unset | show

set L2Param

Set Layer 2 related global settings on the NetScaler

Synopsys

set L2Param [-mbfPeermacUpdate <positive_integer>] [-maxBridgeCollision <positive_integer>] [-bdggrpProxyArp ( ENABLED | DISABLED )] [-bdgSetting ( ENABLED | DISABLED )] [-garpOnVridIntf ( ENABLED | DISABLED )] [-macModeFwdMyPkt ( ENABLED | DISABLED )] [-useMyMAC ( ENABLED | DISABLED )] [-proxyArp ( ENABLED | DISABLED )] [-garpReply ( ENABLED | DISABLED )] [-mbfInstLearning ( ENABLED | DISABLED )] [-rstIntfOnHaFo ( ENABLED | DISABLED )] [-skipProxyingBsdTraffic ( ENABLED | DISABLED )] [-returnToEthernetSender ( ENABLED | DISABLED )]

Arguments

mbfPeermacUpdate

When mbf_instant_learning is enabled, learn any changes in peer's MAC after this time interval, which is in 10ms ticks.

Default value: 10

Minimum value: 0

maxBridgeCollision

Maximum bridge collision for loop detection

Default value: 20

Minimum value: 0

bdggrpProxyArp

Set/reset proxy ARP in bridge group deployment

Possible values: ENABLED, DISABLED

Default value: ENABLED

bdgSetting

Bridging settings for C2C behavior

Possible values: ENABLED, DISABLED

Default value: DISABLED

garpOnVridIntf

Send GARP messagess on VRID-configured interfaces upon failover

Possible values: ENABLED, DISABLED

Default value: ENABLED

macModeFwdMyPkt

MAC mode vserver forward packets destined to VIPs.

Possible values: ENABLED, DISABLED

Default value: DISABLED

useMyMAC

Set/reset cfg_use_my_mac

Possible values: ENABLED, DISABLED

Default value: DISABLED

proxyArp

Set/reset cfg_proxy_arp_dr

Possible values: ENABLED, DISABLED

Default value: ENABLED

garpReply

Set/reset REPLY form of GARP

Possible values: ENABLED, DISABLED

Default value: DISABLED

mbfInstLearning

Enable instant learning of MAC changes in MBF mode.

Possible values: ENABLED, DISABLED

Default value: DISABLED

rstIntfOnHaFo

Enable the reset interface upon HA failover.

Possible values: ENABLED, DISABLED

Default value: DISABLED

skipProxyingBsdTraffic

Enable the proxying of FreeBSD traffic.

Possible values: ENABLED, DISABLED

Default value: DISABLED

returnToEthernetSender

Return to ethernet sender.

Possible values: ENABLED, DISABLED

Default value: DISABLED

unset L2Param

Use this command to remove L2Param settings.Refer to the set L2Param command for meanings of the arguments.

Synopsys

unset L2Param [-mbfPeermacUpdate] [-maxBridgeCollision] [-bdggrpProxyArp] [-bdgSetting] [-garpOnVridIntf] [-macModeFwdMyPkt] [-useMyMAC] [-proxyArp] [-garpReply] [-mbfInstLearning] [-rstIntfOnHaFo] [-skipProxyingBsdTraffic] [-returnToEthernetSender]

show L2Param

Displays the settings of global Layer 2 parameters on the NetScaler appliance.

Synopsys

show L2Param

Outputs

maxBridgeCollision

Maximum bridge collision for loop detection

linkMTU

this MTU is used for Ready logo purpose, changing the Interface MTU at soft layer level.

mbfPeermacUpdate

When mbf_instant_learning is enabled, learn any changes in peer's MAC after this time interval, which is in 10ms ticks.

bdggrpProxyArp

Set/reset proxy ARP in bridge group deployment

bdgSetting

Bridging settings for C2C behavior

garpOnVridIntf

Send GARP messagess on VRID-configured interfaces upon failover

macModeFwdMyPkt

MAC mode vserver forward packets destined to VIPs.

useMyMAC

Set/reset cfg_use_my_mac

proxyArp

Set/reset cfg_proxy_arp_dr

garpReply

Set/reset REPLY form of GARP

mbfInstLearning

Enable instant learning of MAC changes in MBF mode.

rstIntfOnHaFo

Enable the reset interface upon HA failover.

skipProxyingBsdTraffic

Enable the proxying of FreeBSD traffic.

returnToEthernetSender

Return to ethernet sender.

Was this article helpful?