ns ip6¶
The following operations can be performed on "ns ip6":
add ns ip6¶
Creates an IPv6 address on the NetScaler appliance.
Synopsys¶
add ns ip6 <IPv6Address>@ [-scope ( global | link-local )] [-type <type> [-hostRoute ( ENABLED | DISABLED ) [-tag <positive_integer>] [-ip6hostRtGw <ipv6_addr|*>] [-metric <integer>] [-vserverRHILevel <vserverRHILevel>] [-ospf6LSAType ( INTRA_AREA | EXTERNAL ) [-ospfArea <positive_integer>]]] ] [-vlan <positive_integer>] [-nd ( ENABLED | DISABLED )] [-icmp ( ENABLED | DISABLED )] [-vServer ( ENABLED | DISABLED )] [-telnet ( ENABLED | DISABLED )] [-ftp ( ENABLED | DISABLED )] [-gui <gui>] [-ssh ( ENABLED | DISABLED )] [-snmp ( ENABLED | DISABLED )] [-mgmtAccess ( ENABLED | DISABLED )] [-restrictAccess ( ENABLED | DISABLED )] [-dynamicRouting ( ENABLED | DISABLED )] [-networkRoute ( ENABLED | DISABLED )] [-state ( DISABLED | ENABLED )] [-map <ip_addr>] [-vrID6 <positive_integer>] [-ownerNode <positive_integer>] [-ownerDownResponse ( YES | NO )] [-td <positive_integer>]
Arguments¶
IPv6Address
IPv6 address to create on the NetScaler appliance.
scope
Scope of the IPv6 address to be created. Cannot be changed after the IP address is created.
Possible values: global, link-local
Default value: global
type
Type of IP address to be created on the NetScaler appliance. Cannot be changed after the IP address is created.
Possible values: NSIP, VIP, SNIP, GSLBsiteIP, ADNSsvcIP, RADIUSListenersvcIP, CLIP
Default value: SNIP
vlan
The VLAN number.
Default value: 0
Minimum value: 0
Maximum value: 4094
nd
Respond to Neighbor Discovery (ND) requests for this IP address.
Possible values: ENABLED, DISABLED
Default value: ENABLED
icmp
Respond to ICMP requests for this IP address.
Possible values: ENABLED, DISABLED
Default value: ENABLED
vServer
Enable or disable the state of all the virtual servers associated with this VIP6 address.
Possible values: ENABLED, DISABLED
Default value: ENABLED
telnet
Allow Telnet access to this IP address.
Possible values: ENABLED, DISABLED
Default value: ENABLED
ftp
Allow File Transfer Protocol (FTP) access to this IP address.
Possible values: ENABLED, DISABLED
Default value: ENABLED
gui
Allow graphical user interface (GUI) access to this IP address.
Possible values: ENABLED, SECUREONLY, DISABLED
Default value: ENABLED
ssh
Allow secure Shell (SSH) access to this IP address.
Possible values: ENABLED, DISABLED
Default value: ENABLED
snmp
Allow Simple Network Management Protocol (SNMP) access to this IP address.
Possible values: ENABLED, DISABLED
Default value: ENABLED
mgmtAccess
Allow access to management applications on this IP address.
Possible values: ENABLED, DISABLED
Default value: DISABLED
restrictAccess
Block access to nonmanagement applications on this IP address. This option is applicable forMIP6s, SNIP6s, and NSIP6s, and is disabled by default. Nonmanagement applications can run on the underlying NetScaler Free BSD operating system.
Possible values: ENABLED, DISABLED
Default value: DISABLED
dynamicRouting
Allow dynamic routing on this IP address. Specific to Subnet IPv6 (SNIP6) address.
Possible values: ENABLED, DISABLED
Default value: DISABLED
hostRoute
Option to push the VIP6 to ZebOS routing table for Kernel route redistribution through dynamic routing protocols.
Possible values: ENABLED, DISABLED
networkRoute
Option to push the SNIP6 subnet to ZebOS routing table for Kernel route redistribution through dynamic routing protocol.
Possible values: ENABLED, DISABLED
tag
Tag value for the network/host route associated with this IP.
Default value: 0
Minimum value: 0
ip6hostRtGw
IPv6 address of the gateway for the route. If Gateway is not set, VIP uses :: as the gateway.
Default value: 0
metric
Integer value to add to or subtract from the cost of the route advertised for the VIP6 address.
Minimum value: -16777215
vserverRHILevel
Advertise or do not advertise the route for the Virtual IP (VIP6) address on the basis of the state of the virtual servers associated with that VIP6.
-
NONE - Advertise the route for the VIP6 address, irrespective of the state of the virtual servers associated with the address.
-
ONE VSERVER - Advertise the route for the VIP6 address if at least one of the associated virtual servers is in UP state.
-
ALL VSERVER - Advertise the route for the VIP6 address if all of the associated virtual servers are in UP state.
-
VSVR_CNTRLD. Advertise the route for the VIP address according to the RHIstate (RHI STATE) parameter setting on all the associated virtual servers of the VIP address along with their states.
When Vserver RHI Level (RHI) parameter is set to VSVR_CNTRLD, the following are different RHI behaviors for the VIP address on the basis of RHIstate (RHI STATE) settings on the virtual servers associated with the VIP address:
-
If you set RHI STATE to PASSIVE on all virtual servers, the NetScaler ADC always advertises the route for the VIP address.
-
If you set RHI STATE to ACTIVE on all virtual servers, the NetScaler ADC advertises the route for the VIP address if at least one of the associated virtual servers is in UP state.
*If you set RHI STATE to ACTIVE on some and PASSIVE on others, the NetScaler ADC advertises the route for the VIP address if at least one of the associated virtual servers, whose RHI STATE set to ACTIVE, is in UP state.
Possible values: ONE_VSERVER, ALL_VSERVERS, NONE, VSVR_CNTRLD
Default value: ONE_VSERVER
ospf6LSAType
Type of LSAs to be used by the IPv6 OSPF protocol, running on the NetScaler appliance, for advertising the route for the VIP6 address.
Possible values: INTRA_AREA, EXTERNAL
Default value: EXTERNAL
ospfArea
ID of the area in which the Intra-Area-Prefix LSAs are to be advertised for the VIP6 address by the IPv6 OSPF protocol running on the NetScaler appliance. When ospfArea is not set, VIP6 is advertised on all areas.
Default value: -1
Minimum value: 0
Maximum value: 4294967294LU
state
Enable or disable the IP address.
Possible values: DISABLED, ENABLED
Default value: ENABLED
map
Mapped IPV4 address for the IPV6 address.
vrID6
A positive integer that uniquely identifies a VMAC address for binding to this VIP address. This binding is used to set up NetScaler appliances in an active-active configuration using VRRP.
Minimum value: 1
Maximum value: 255
ownerNode
ID of the cluster node for which you are adding the IP address. Must be used if you want the IP address to be active only on the specific node. Can be configured only through the cluster IP address. Cannot be changed after the IP address is created.
Default value: 255
Minimum value: 0
ownerDownResponse
in cluster system, if the owner node is down, whether should it respond to icmp/arp
Possible values: YES, NO
Default value: YES
td
Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0.
Minimum value: 0
Maximum value: 4094
Example¶
add ns ip6 2001::a/96 -scope GLOBAL
rm ns ip6¶
Removes an IPv6 address configured on the NetScaler appliance.
Synopsys¶
rm ns ip6 <IPv6Address>@ [-td <positive_integer>]
Arguments¶
IPv6Address
IPv6 address that you want to remove.
td
Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0.
Minimum value: 0
Maximum value: 4094
Example¶
rm ns ip6 2002::5
set ns ip6¶
Modifies the specified parameters of an IPv6 address configured on the NetScaler appliance.
Synopsys¶
set ns ip6 (<IPv6Address>@ [-td <positive_integer>]) [-nd ( ENABLED | DISABLED )] [-icmp ( ENABLED | DISABLED )] [-vServer ( ENABLED | DISABLED )] [-telnet ( ENABLED | DISABLED )] [-ftp ( ENABLED | DISABLED )] [-gui <gui>] [-ssh ( ENABLED | DISABLED )] [-snmp ( ENABLED | DISABLED )] [-mgmtAccess ( ENABLED | DISABLED )] [-ownerDownResponse ( YES | NO )] [-restrictAccess ( ENABLED | DISABLED )] [-state ( DISABLED | ENABLED )] [-map <ip_addr>] [-dynamicRouting ( ENABLED | DISABLED )] [-hostRoute ( ENABLED | DISABLED )] [-networkRoute ( ENABLED | DISABLED )] [-ip6hostRtGw <ipv6_addr|*>] [-metric <integer>] [-vserverRHILevel <vserverRHILevel>] [-ospf6LSAType ( INTRA_AREA | EXTERNAL ) [-ospfArea <positive_integer>]] [-tag <positive_integer>] [-vrID6 <positive_integer>]
Arguments¶
IPv6Address
IPv6 address whose parameters you want to modify.
td
Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0.
Minimum value: 0
Maximum value: 4094
nd
The state of ND responses for the entity.
Possible values: ENABLED, DISABLED
Default value: ENABLED
icmp
The state of ICMP responses for the entity.
Possible values: ENABLED, DISABLED
Default value: ENABLED
vServer
The state of vserver attribute for this IP entity.
Possible values: ENABLED, DISABLED
Default value: ENABLED
telnet
The state of telnet access to this IP entity.
Possible values: ENABLED, DISABLED
Default value: ENABLED
ftp
The state of ftp access to this IP entity.
Possible values: ENABLED, DISABLED
Default value: ENABLED
gui
The state of GUI access to this IP entity.
Possible values: ENABLED, SECUREONLY, DISABLED
Default value: ENABLED
ssh
The state of SSH access to this IP entity.
Possible values: ENABLED, DISABLED
Default value: ENABLED
snmp
The state of SNMP access to this IP entity.
Possible values: ENABLED, DISABLED
Default value: ENABLED
mgmtAccess
The state of management access to this IP entity.
Possible values: ENABLED, DISABLED
Default value: DISABLED
ownerDownResponse
in cluster system, if the owner node is down, whether should it respond to icmp/arp
Possible values: YES, NO
Default value: YES
restrictAccess
Status of ports not used for management access (blocked/open) for the entity.
Possible values: ENABLED, DISABLED
Default value: DISABLED
state
Enable or disable the IP address.
Possible values: DISABLED, ENABLED
Default value: ENABLED
map
Mapped IPV4 address for the IPV6 address.
dynamicRouting
Allow dynamic routing on this IP address. Specific to Subnet IPv6 (SNIP6) address.
Possible values: ENABLED, DISABLED
Default value: DISABLED
hostRoute
Option to push the VIP6 to ZebOS routing table for Kernel route redistribution through dynamic routing protocols.
Possible values: ENABLED, DISABLED
networkRoute
Option to push the SNIP6 subnet to ZebOS routing table for Kernel route redistribution through dynamic routing protocol.
Possible values: ENABLED, DISABLED
ip6hostRtGw
IPv6 address of the gateway for the route. If Gateway is not set, VIP uses :: as the gateway.
Default value: 0
metric
Integer value to add to or subtract from the cost of the route advertised for the VIP6 address.
Minimum value: -16777215
vserverRHILevel
Advertise or do not advertise the route for the Virtual IP (VIP6) address on the basis of the state of the virtual servers associated with that VIP6.
-
NONE - Advertise the route for the VIP6 address, irrespective of the state of the virtual servers associated with the address.
-
ONE VSERVER - Advertise the route for the VIP6 address if at least one of the associated virtual servers is in UP state.
-
ALL VSERVER - Advertise the route for the VIP6 address if all of the associated virtual servers are in UP state.
-
VSVR_CNTRLD. Advertise the route for the VIP address according to the RHIstate (RHI STATE) parameter setting on all the associated virtual servers of the VIP address along with their states.
When Vserver RHI Level (RHI) parameter is set to VSVR_CNTRLD, the following are different RHI behaviors for the VIP address on the basis of RHIstate (RHI STATE) settings on the virtual servers associated with the VIP address:
-
If you set RHI STATE to PASSIVE on all virtual servers, the NetScaler ADC always advertises the route for the VIP address.
-
If you set RHI STATE to ACTIVE on all virtual servers, the NetScaler ADC advertises the route for the VIP address if at least one of the associated virtual servers is in UP state.
*If you set RHI STATE to ACTIVE on some and PASSIVE on others, the NetScaler ADC advertises the route for the VIP address if at least one of the associated virtual servers, whose RHI STATE set to ACTIVE, is in UP state.
Possible values: ONE_VSERVER, ALL_VSERVERS, NONE, VSVR_CNTRLD
Default value: ONE_VSERVER
ospf6LSAType
Type of LSAs to be used by the IPv6 OSPF protocol, running on the NetScaler appliance, for advertising the route for the VIP6 address.
Possible values: INTRA_AREA, EXTERNAL
Default value: EXTERNAL
ospfArea
ID of the area in which the Intra-Area-Prefix LSAs are to be advertised for the VIP6 address by the IPv6 OSPF protocol running on the NetScaler appliance. When ospfArea is not set, VIP6 is advertised on all areas.
Default value: -1
Minimum value: 0
Maximum value: 4294967294LU
tag
Tag value for the network/host route associated with this IP.
Default value: 0
Minimum value: 0
vrID6
A positive integer that uniquely identifies a VMAC address for binding to this VIP address. This binding is used to set up NetScaler appliances in an active-active configuration using VRRP.
Minimum value: 1
Maximum value: 255
Example¶
set ns ip6 2001::a -map 10.102.33.27
unset ns ip6¶
Modifies the parameters of an IPv6 address configured on the NetScaler appliance..Refer to the set ns ip6 command for meanings of the arguments.
Synopsys¶
unset ns ip6 <IPv6Address>@ [-td <positive_integer>] [-ospfArea] [-nd] [-icmp] [-vServer] [-telnet] [-ftp] [-gui] [-ssh] [-snmp] [-mgmtAccess] [-ownerDownResponse] [-restrictAccess] [-state] [-map] [-dynamicRouting] [-hostRoute] [-networkRoute] [-ip6hostRtGw] [-metric] [-vserverRHILevel] [-ospf6LSAType] [-tag] [-vrID6]
Example¶
unset ns ip6 2001::a -ospfArea
show ns ip6¶
Displays settings of all the IPv6 addresses or of the specified IPv6 address configured on the NetScaler appliance. To display settings of all the IPv6 addresses, run the command without any parameters. To display settings of a particular IPv6 address, specify the IPv6 address.
Synopsys¶
show ns ip6 [<IPv6Address> [-td <positive_integer>]]
Arguments¶
IPv6Address
IPv6 address whose settings you want the NetScaler appliance to display.
td
Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0.
Minimum value: 0
Maximum value: 4094
Outputs¶
scope
Scope of the IPv6 address to be created. Cannot be changed after the IP address is created.
type
The type of the IPV6 address
ipType
The type of the IPv6 address
vlan
The VLAN number.
nd
Whether ND is enabled or disabled.
icmp
Whether icmp is enabled or disabled.
vServer
Whether vserver is enabled or disabled.
telnet
Whether telnet is enabled or disabled.
ssh
Whether ssh is enabled or disabled.
gui
Whether gui is (enabled|SecureOnly|disabled).
snmp
Whether snmp is enabled or disabled.
ftp
Whether ftp is enabled or disabled.
mgmtAccess
Whether management access is enabled or disabled.
restrictAccess
Blocking of all ports not used for management access enabled or disabled
state
Current state of this IP.
map
Mapped IPV4 address for the IPV6 address.
dynamicRouting
Allow dynamic routing on this IP address. Specific to Subnet IPv6 (SNIP6) address.
hostRoute
Option to push the VIP6 to ZebOS routing table for Kernel route redistribution through dynamic routing protocols.
networkRoute
Option to push the SNIP6 subnet to ZebOS routing table for Kernel route redistribution through dynamic routing protocol.
tag
Tag value for the network/host route associated with this IP.
ip6hostRtGw
IPv6 address of the gateway for the route. If Gateway is not set, VIP uses :: as the gateway.
metric
The metric value to be added or subtracted from the cost of the route advertised for this IPv6 entity.
vserverRHILevel
Advertise or do not advertise the route for the Virtual IP (VIP6) address on the basis of the state of the virtual servers associated with that VIP6.
-
NONE - Advertise the route for the VIP6 address, irrespective of the state of the virtual servers associated with the address.
-
ONE VSERVER - Advertise the route for the VIP6 address if at least one of the associated virtual servers is in UP state.
-
ALL VSERVER - Advertise the route for the VIP6 address if all of the associated virtual servers are in UP state.
-
VSVR_CNTRLD. Advertise the route for the VIP address according to the RHIstate (RHI STATE) parameter setting on all the associated virtual servers of the VIP address along with their states.
When Vserver RHI Level (RHI) parameter is set to VSVR_CNTRLD, the following are different RHI behaviors for the VIP address on the basis of RHIstate (RHI STATE) settings on the virtual servers associated with the VIP address:
-
If you set RHI STATE to PASSIVE on all virtual servers, the NetScaler ADC always advertises the route for the VIP address.
-
If you set RHI STATE to ACTIVE on all virtual servers, the NetScaler ADC advertises the route for the VIP address if at least one of the associated virtual servers is in UP state.
*If you set RHI STATE to ACTIVE on some and PASSIVE on others, the NetScaler ADC advertises the route for the VIP address if at least one of the associated virtual servers, whose RHI STATE set to ACTIVE, is in UP state.
VIPrtadv2BSD
Whether this route is advertised to FreeBSD
VIPvserCount
Number of vservers bound to this VIP
VIPvserDownCount
Number of vservers bound to this VIP, which are down
ospf6LSAType
The OSPF's route advertisement type.
ospfArea
The area ID of the area in which OSPF INTRA AREA PREFIX LSAs should be advertised. When ospfArea is not set, LSAs are advertised in all areas.
ownerNode
ID of the cluster node for which you are adding the IP address. Must be used if you want the IP address to be active only on the specific node. Can be configured only through the cluster IP address. Cannot be changed after the IP address is created.
stateflag
vrID6
A positive integer that uniquely identifies a VMAC address for binding to this VIP address. This binding is used to set up NetScaler appliances in an active-active configuration using VRRP.
cfgflags
This contains the flags for IP in DB
ipRefcount
Used to keep reference count of IPv6
ownerDownResponse
in cluster system, if the owner node is down, whether should it respond to icmp/arp
systemType
The type of the System. Possible Values: Standalone, HA, Cluster. Used for display purpose.
devno
count
Example¶
show ns ip6