Download full document:

ipv6

Configuration for ip v6 resource.

Properties

(click to see Operations)

NameData TypePermissionsDescription
ralearning<String>Read-writeEnable the NetScaler appliance to learn about various routes from Router Advertisement (RA) and Router Solicitation (RS) messages sent by the routers.
Default value: DISABLED
Possible values = ENABLED, DISABLED
routerredirection<String>Read-writeEnable the NetScaler appliance to do Router Redirection.
Default value: DISABLED
Possible values = ENABLED, DISABLED
ndbasereachtime<Double>Read-writeBase reachable time of the Neighbor Discovery (ND6) protocol. The time, in milliseconds, that the NetScaler appliance assumes an adjacent device is reachable after receiving a reachability confirmation.
Default value: 30000
Minimum value = 1
ndretransmissiontime<Double>Read-writeRetransmission time of the Neighbor Discovery (ND6) protocol. The time, in milliseconds, between retransmitted Neighbor Solicitation (NS) messages, to an adjacent device.
Default value: 1000
Minimum value = 1
natprefix<String>Read-writePrefix used for translating packets from private IPv6 servers to IPv4 packets. This prefix has a length of 96 bits (128-32 = 96). The IPv6 servers embed the destination IP address of the IPv4 servers or hosts in the last 32 bits of the destination IP address field of the IPv6 packets. The first 96 bits of the destination IP address field are set as the IPv6 NAT prefix. IPv6 packets addressed to this prefix have to be routed to the NetScaler appliance to ensure that the IPv6-IPv4 translation is done by the appliance.
td<Double>Read-writeInteger value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0.
Default value: 0
Minimum value = 0
Maximum value = 4094
dodad<String>Read-writeEnable the NetScaler appliance to do Duplicate Address
Detection (DAD) for all the NetScaler owned IPv6 addresses regardless of whether they are obtained through stateless auto configuration, DHCPv6, or manual configuration.
Default value: DISABLED
Possible values = ENABLED, DISABLED
basereachtime<Integer>Read-onlyND6 base reachable time (ms).
reachtime<Integer>Read-onlyND6 computed reachable time (ms).
ndreachtime<Double>Read-onlyND6 computed reachable time (ms).
retransmissiontime<Integer>Read-onlyND6 retransmission time (ms).
__count<Double>Read-onlycount parameter

Operations

(click to see Properties)

UPDATE| UNSET| GET (ALL)| GET| COUNT

Some options that you can use for each operations:

  • Getting warnings in response:NITRO allows you to get warnings in an operation by specifying the "warning" query parameter as "yes". For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

    http://<netscaler-ip-address>/nitro/v1/config/login?warning=yes

    If any, the warnings are displayed in the response payload with the HTTP code "209 X-NITRO-WARNING".

  • Authenticated access for individual NITRO operations:NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

    To do this, you must specify the username and password in the request header of the NITRO request as follows:

    X-NITRO-USER:<username>

    X-NITRO-PASS:<password>

    Note:In such cases, make sure that the request header DOES not include the following:

    Cookie:NITRO_AUTH_TOKEN=<tokenvalue>

Note:

Mandatory parameters are marked in redand placeholder content is marked in <green>.

update

URL:http://<netscaler-ip-address>/nitro/v1/config/ipv6

HTTP Method:PUT

Request Headers:

Cookie:NITRO_AUTH_TOKEN=<tokenvalue> Content-Type:application/json

Request Payload:

{"ipv6":{
"ralearning":<String_value>,
"routerredirection":<String_value>,
"ndbasereachtime":<Double_value>,
"ndretransmissiontime":<Double_value>,
"natprefix":<String_value>,
"td":<Double_value>,
"dodad":<String_value>
}}

Response:

HTTP Status Code on Success: 200 OK HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

unset

URL:http://<netscaler-ip-address>/nitro/v1/config/ipv6?action=unset

HTTP Method:POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN=<tokenvalue> Content-Type:application/json

Request Payload:

{"ipv6":{
"ralearning":true,
"routerredirection":true,
"ndbasereachtime":true,
"ndretransmissiontime":true,
"natprefix":true,
"td":<Double_value>,
"dodad":true
}}

Response:

HTTP Status Code on Success: 200 OK HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

get (all)

URL:http://<netscaler-ip-address>/nitro/v1/config/ipv6

Query-parameters:

attrs

http://<netscaler-ip-address>/nitro/v1/config/ipv6?attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

filter

http://<netscaler-ip-address>/nitro/v1/config/ipv6?filter=property-name1:property-val1,property-name2:property-val2

Use this query-parameter to get the filtered set of ipv6 resources configured on NetScaler.Filtering can be done on any of the properties of the resource.

view

http://<netscaler-ip-address>/nitro/v1/config/ipv6?view=summary

Note:By default, the retrieved results are displayed in detail view (?view=detail).

pagination

http://<netscaler-ip-address>/nitro/v1/config/ipv6?pagesize=#no;pageno=#no

Use this query-parameter to get the ipv6 resources in chunks.

HTTP Method:GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN=<tokenvalue> Accept:application/json

Response:

HTTP Status Code on Success: 200 OK HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the errorResponse Headers:

Content-Type:application/json

Response Payload:

{ "ipv6": [ {
"td":<Double_value>,
"ralearning":<String_value>,
"routerredirection":<String_value>,
"basereachtime":<Integer_value>,
"ndbasereachtime":<Double_value>,
"reachtime":<Integer_value>,
"ndreachtime":<Double_value>,
"retransmissiontime":<Integer_value>,
"ndretransmissiontime":<Double_value>,
"natprefix":<String_value>,
"dodad":<String_value>
}]}

get

URL:http://<netscaler-ip-address>/nitro/v1/config/ipv6/td_value<Double>

Query-parameters:

attrs

http://<netscaler-ip-address>/nitro/v1/config/ipv6/td_value<Double>?attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

view

http://<netscaler-ip-address>/nitro/v1/config/ipv6/td_value<Double>?view=summary

Note:By default, the retrieved results are displayed in detail view (?view=detail).

HTTP Method:GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN=<tokenvalue> Accept:application/json

Response:

HTTP Status Code on Success: 200 OK HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the errorResponse Headers:

Content-Type:application/json

Response Payload:

{ "ipv6": [ {
"td":<Double_value>,
"ralearning":<String_value>,
"routerredirection":<String_value>,
"basereachtime":<Integer_value>,
"ndbasereachtime":<Double_value>,
"reachtime":<Integer_value>,
"ndreachtime":<Double_value>,
"retransmissiontime":<Integer_value>,
"ndretransmissiontime":<Double_value>,
"natprefix":<String_value>,
"dodad":<String_value>
}]}

count

URL:http://<netscaler-ip-address>/nitro/v1/config/ipv6?count=yes

HTTP Method:GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN=<tokenvalue> Accept:application/json

Response:

HTTP Status Code on Success: 200 OK HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the errorResponse Headers:

Content-Type:application/json

Response Payload:

{ "ipv6": [ { "__count": "#no"} ] }